Revistas
Autores:
Martins, C. A. (Autor de correspondencia); de Faria, G. L.; Mayo, Unai; et al.
Revista:
METALS
ISSN:
2075-4701
Año:
2023
Vol.:
13
N°:
2
Págs.:
405
Obtaining high levels of mechanical properties in steels is directly linked to the use of special mechanical forming processes and the addition of alloying elements during their manufacture. This work presents a study of a hot-rolled steel strip produced to achieve a yield strength above 600 MPa, using a niobium microalloyed HSLA steel with non-stoichiometric titanium (titanium/nitrogen ratio above 3.42), and rolled on a Steckel mill. A major challenge imposed by rolling on a Steckel mill is that the process is reversible, resulting in long interpass times, which facilitates recrystallization and grain growth kinetics. Rolling parameters whose aim was to obtain the maximum degree of microstructural refinement were determined by considering microstructural evolution simulations performed in MicroSim-SM (R) software and studying the alloy through physical simulations to obtain critical temperatures and determine the CCT diagram. Four ranges of coiling temperatures (525-550 degrees C/550-600 degrees C/600-650 degrees C/650-700 degrees C) were applied to evaluate their impact on microstructure, precipitation hardening, and mechanical properties, with the results showing a very refined microstructure, with the highest yield strength observed at coiling temperatures of 600-650 degrees C. This scenario is explained by the maximum precipitation of titanium carbide observed at this temperature, leading to a greater contribution of precipitation hardening provided by the presence of a large volume of small-sized precipitates. This paper shows that the combination of optimized industrial parameters based on metallurgical mechanisms and advanced modeling techniques opens up new possibilities for a robust production of high-strength steels using a Steckel mill. The microstructural base for a stable production of high-strength hot-rolled products relies on a consistent grain size refinement provided mainly by the effect of Nb together with appropriate rolling parameters, and the fine precipitation of TiC during cooling provides the additional increase to reach the requested yield strength values.
Revista:
METALS
ISSN:
2075-4701
Año:
2021
Vol.:
11
N°:
1
Págs.:
112
Intercritically deformed steels present combinations of different types of ferrite, such as deformed ferrite (DF) and non-deformed ferrite (NDF) grains, which are transformed during the final deformation passes and final cooling step. Recently, a grain identification and correlation technique based on EBSD has been employed together with a discretization methodology, enabling a distinction to be drawn between different ferrite populations (NDF and DF grains). This paper presents a combination of interrupted tensile tests with crystallographic characterization performed by means of Electron Backscatter Diffraction (EBSD), by analyzing the evolution of an intercritically deformed micro-alloyed steel. In addition to this, and using the nanoindentation technique, both ferrite families were characterized micromechanically and the nanohardness was quantified for each population. NDF grains are softer than DF ones, which is related to the presence of a lower fraction of low-angle grain boundaries. The interrupted tensile tests show the different behavior of low- and high-angle grain boundary evolution as well as the strain partitioning in each ferrite family. NDF population accommodates most of the deformation at initial strain intervals, since strain reaches 10%. For higher strains, NDF and DF grains behave similarly to the strain applied.
Revista:
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
ISSN:
0921-5093
The mechanical properties of intercritically rolled microstructures have been scarcely reported in literature. Although the strengthening effect of intercritical rolling is generally recognized, there is no a clear opinion on its effect on toughness. Therefore, a greater knowledge of how different process parameters affect the mechanical properties during intercritical deformation is required. With the aim of evaluating the relationship between microstructure and mechanical properties on intercritically deformed low carbon steels, plane strain compression tests were carried out. Plane strain compression tests allow for both the characterization of the microstructural features and the evaluation of mechanical properties, via tensile and Charpy tests. Firstly, the intercritically deformed microstructures were characterized using the EBSD technique, and then a discretization methodology was used to distinguish both intercritically deformed and non-deformed ferrite populations. Next, strength and toughness properties were measured by means of tensile and Charpy tests. The results indicate that the reduction of the deformation temperature leads to an increment of yield strength for both steels, but at the same time toughness properties worsen. Deformed ferrite fractions higher than 25% result in a very pronounced loss of ductility. The yield strength was predicted by estimating the contribution of different strengthening mechanisms (solid solution, grain size refinement, dislocation density) corresponding to each ferrite population by considering a nonlinear law of mixtures. Similarly, the impact of different microstructural parameters (solid solution, grain size, microstructural heterogeneity, contribution of dislocation density and secondary phases) on toughness was evaluated and a new equation able to predict ductile to brittle transition temperature for intercritically deformed microstructures was developed.
Revista:
MATERIALS CHARACTERIZATION
ISSN:
1044-5803
Año:
2019
Vol.:
147
Págs.:
31 - 42
Heavy gauge structural plates has been widely rolled in the austenite/ferrite two phase region, in order to meet the demanding market requirements regarding tensile properties. Even though strength levels can be increased by intercritical rolling, toughness properties may be impaired. Therefore, a greater knowledge of how different austenite-ferrite balances affect the microstructural evolution during intercritical deformation is required. With the aim of gaining a deep comprehension of the evolution of the microstructure during intercritical deformation, dilatometry tests were performed simulating intercritical rolling conditions. Different ferrite populations are identified in the resulting microstructures, composed of intercritically deformed ferrite and non-deformed ferrite transformed during final air cooling. In the deformed ferrite grains well defined substructure is clearly noticed, whereas the non-deformed grains formed during air cooling step do not show any evidence of substructure. In the current work, EBSD advanced characterization technique was used to develop a methodology that is able to differentiate the intercritically deformed ferrite from non-deformed ferrite for low carbon steels. Based on the Grain Orientation Spread (GOS) parameter, a threshold value of 2 degrees was defined to distinguish deformed and non deformed ferrite grains. The proposed procedure allows distinguishing both ferrite populations and quantifying microstructural parameters of each family. The effect of the addition of C and austenite-ferrite balance on the microstructural evolution of each ferrite type was analyzed.
Revista:
METALS
ISSN:
2075-4701
Año:
2019
Vol.:
9
N°:
10
Págs.:
1049
Heavy gauge line pipe and structural steel plate materials are often rolled in the two-phase region for strength reasons. However, strength and toughness show opposite trends, and the exact effect of each rolling process parameter remains unclear. Even though intercritical rolling has been widely studied, the specific mechanisms that act when different microalloying elements are added remain unclear. To investigate this further, laboratory thermomechanical simulations reproducing intercritical rolling conditions were performed in plain low carbon and NbV-microalloyed steels. Based on a previously developed procedure using electron backscattered diffraction (EBSD), the discretization between intercritically deformed ferrite and new ferrite grains formed after deformation was extended to microalloyed steels. The austenite conditioning before intercritical deformation in the Nb-bearing steel affects the balance of final precipitates by modifying the size distributions and origin of the Nb (C, N). This fact could modify the substructure in the intercritically deformed grains. A simple transformation model is proposed to predict average grain sizes under intercritical deformation conditions.